These Champion® split system air conditioner models are completely assembled, piped, and wired at the factory to provide one-piece shipment and rigging. Each unit is pressurized with a holding charge of R-22 for storage and/or shipping. The compact design, clean styling, and quiet operation make these condensing units suitable for almost any outdoor location. On rooftops, because they weigh much less than a single-package unit of similar capacity and are much easier to rig and support. At ground level, because their ample sub-cooling capacity allows them to be located 60 feet below the evaporator coil. All sheet metal parts are constructed of commercial grade (G90) galvanized steel, powder-paint coated to withstand a 750-hour salt spray test. A complete line of evaporator blower units is offered to meet your precise capacity and air-handling requirements.

Beneficios Especiales

• Built for efficient operation, long life, and moderate installation costs.
• All units have matching York upflow or horizontal coils for non-furnace installations.
• Offered in 208/230, 460, and 575 voltages are easy to handle. They have base rails with forklift access and rigging holes.
• Low ambient operation to 45°F is standard, and accessories for 0°F low ambient operation are available.
• Installation time and costs are reduced by easy power and control wiring.
• All units are factory wired, piped, charged, and tested prior to shipment.
• Factory-installed options further reduce installation costs.
• Electric utility knockouts are provided on unit side and bottom for easy connections.
• Full-perimeter base rails are permanently attached to provide a solid unit foundation and fork lift access.
• Compressor is internally protected against high pressure and temperature.
• Grooved copper tubes and enhanced aluminum fin construction improve heat transfer.
• Permanently lubricated condenser and evaporator fan motor bearings need no annual maintenance.

Beneficios Especiales

• Meets or exceeds Ashrae 90.1-1999 standards
• Simplicity Controls
• Inherently protect condenser fan motors
• V-Coil Design with exterior service port connections
• Five-minute anti-short cycle timer and miniumum compressor run time
• Standard operation to 40 F. Field-installed
• Low Ambient VFD Control to 0ºF
• Factory installed disconnect and Technicoat coils option
• Scroll compressors provide both high efficiency and reliability
• Condenser coils are constructed of copper tubes and aluminum fins for durability and long lasting efficient operation
• Crankcase heaters that will be de-energized when the compressor is operating
• Self contained high and low pressure controls
• Solid state or internal line break compressor motor protection
• Class 2, 24-volt thermostat control circuit
• A sight glass and filter-drier is shipped in the unit's control box for field installation in the liquid line
• Copper stub-outs are factory mounted on the suction and liquid lines to simplify the field piping connections
• Multiple controls to provide stable system operation at ambient temperatures down to 40ºF with kits available for operation to 0ºF
• Compressor staging for capacity reduction provides more economical operation and even temperature levels within the conditioned space
• A lockout circuit prevents the unit from cycling on safety control
• Pumpout on unit startup to prevent allowing liquid refrigerant returning to the compressor is standard on 25 through 50 ton models and optional for 15 and 20 tons

The low profile York Olympian® Series is built to the same exacting quality standards demanded of all York equipment, and has earned its own reputation for dependability, quiet operation, and efficiency. Models include: • Olympian 14 Super High Efficiency Air Conditioners (HRE) As with all York condensing units, the HRE models are designed to be custom-matched with a York evaporator section. Matching air handlers are available for upflow, downflow, and horizontal applications. Electric heaters, Gas or Oil furnaces, and add-on coils are also available. With efficiency ratings ranging from 14 SEER to as high as 15.3, when matched to a compatible variable-speed air handler, the Olympian Series is the niche line for homeowners in search of highly affordable home comfort, in terms of both initial installed cost and long-term operation.

Beneficios Especiales

• Coils are constructed of copper tubing with protected aluminum fins for durability and long lasting, efficient operation.
• Plastic mesh coil protection is standard between coil guard and condenser coil.
• Compressor is internally protected against high pressure and temperature through a high-pressure relief valve and temperature sensor.
• Cabinet is fabricated from pre-painted galvanized steel to resist rust and corrosion.
• Special primer and desert tan matted finish diminishes fading from sunlight exposure.

These completely assembled split system evaporator blowers include a well-insulated cabinet, a cooling coil with copper tubes and aluminum fins, expansion valve(s), distributor(s), throw-away filters, a centrifugal blower, a blower motor, an adjustable fan drive, a blower motor contactor, and a small holding charge of R-22. (Blower motors and drives are sold separately on Model LEU 240-600). Units are shipped in the vertical position, ready for field installation. KEU units can easily be installed for horizontal operation. LEU360 and 480 units can be installed in up to 12 different positions and suspended in various positions.

Beneficios Especiales

• 5 to 50 ton. Supply air plenums and return grilles available as field-installed accessories.
• 3-Phase elective Heaters available from 10 Kw up to 72 Kw on KEU models (field installed).
• Steam and hot water coils are available.
• Base and suspension kits are available for raising units from the floor or suspending from the ceiling (up to 20 tons).
• Units can be configured in a variety of positions.
• Motor and drive options are available on 20 to 50 ton units (field installed).

Publicaciones disponibles en inglés:

Application Data - Fan Curves 29 KB

Application Data - Split System Air Conditioners (Fan Curves) 335 KB

Guide Specifications - KEU60 - 180 KES120 57 KB

Submittal Drawing - Split System Evaporator Blower 15 Tons (180) 125 KB

Submittal Drawing - Split System Evaporator Blower 5 Tons 130 KB

Submittal Drawing - Split System Evaporator Blower KEU (090/120) 131 KB

Technical Guide - HCE 180 - 240 Mbh Split System Air Cooled Condensing Unit 672 KB

Technical Guide - K3EU -180 223 KB

Technical Guide - KEU60 - 180 442 KB

Technical Guide - Sunline 2000 Split System Evaporator Blower 7.5 and 10 Nominal Tons 243 KB

A complete offering of field-installed accessories makes the York Champion split system evaporator blower (KES among the most flexible in the industry. From a quality standpoint, these completely assembled units include a well-insulated cabinet, a cooling coil with copper tubes and aluminum fins, expansion valve(s), distributor(s), throw-away filters, a centrifugal blower, a blower motor, an adjustable fan drive, a blower motor contactor, and a small holding charge of R-22. All product units can easily be installed for vertical or horizontal operation, as well as suspended in various positions.

Beneficios Especiales

• Supply air plenums, return air grilles, 3-phase electric heaters, thermostats, steam coils, hot water coils, base sections, and suspension hardware are available as field-installed accessories.
• KES 120 equipped as 10 nominal Tons with two 5-Ton circuits.

These completely assembled split system evaporator blowers include a well-insulated cabinet, a cooling coil with copper tubes and aluminum fins, expansion valve(s), distributor(s), throw-away filters, a centrifugal blower, a blower motor, an adjustable fan drive, a blower motor contactor, and a small holding charge of R-22. Units are shipped in the vertical position, ready for field installation. KEU units can easily be installed for horizontal operation.

Beneficios Especiales

• 20 nominal tons.
• Designed with two distinct modules for maximum application flexibility.
• Blower modules can be repositioned to meet application requirements.
• Coil module includes direct expansion coils, one-inch throw-away filters, liquid line solenoid valves for capacity reduction and pumpdown, thermal expansion valves, distributors, and a condensate drain pan.
• Steam coils, hot water coils, base sections, suspension hardware, blower motors, and drive packages are available as field-installed accessories.

The LA/LB line is a flexible performer. They can be installed in up to 12 different positions and suspended in various positions. Evaporator blower units are designed with two distinct modules to provide maximum application flexibility. The 25, 30 and 40 ton units are shipped as single packages with the blower module mounted on top of the coil module, The blower module can be repositioned in the field to meet almost any installation requirement. Blower and coil modules for the 50 ton units are shipped separately to simplify handling. These modules can be connected in the field with the same flexibility as the smaller units. The blower module includes the blower wheels and room for a field-mounted motor and drive. The coil module includes direct expansion coils, 2 in. throwaway filters, thermal expansion valves, distributors and a condensate drain pan. Every evaporator coil is pressurized with air to 325 psig andleak tested under water. After the headers are brazed onto the coil and the coil is installed in the unit, the coil is pressurized with a combination coil is evacuated and dehydrated, it is pressurized with a holding charge of refrigerant-22 for storage and/or shipping. Steam coils, hot water coils, base sections, suspension hardware, blower motors and drive packages are available as field-installed accessories to provide additional application flexibility. These evaporator blowers, combined with condensing units, provide years of quiet, efficient and dependable operation. These units are manufactured under ISO 9001 Quality System Certification. Units may be bottom-supported or ceiling-suspended and can be arranged to meet almost any space or duct requirements. Each unit is available with a choice of blower motors ,drive packages and other accessories to make them suitable for most applications.

Beneficios Especiales

• Ease of service
• Base sections (25, 30 and 40 Ton only)
• Suspension packages
• Hot water coils
• Steam coils (LA300 and LB360 only)
• Wide range of blower motors
• Variety of drive packages
• Factory-mounted expansion valve and filter-drier in both refrigerant circuit
• Adjustable TXV’s
• Two-inch throwaway filters
• Single point power connection
• One-year limited warranty on all parts.

These completely assembled units include a well-insulated cabinet, a DX cooling coil with copper tubes and aluminum fins, expansion valve(s), distributor(s), throwaway filters, a centrifu-gal blower, a blower motor, an adjustable belt drive, a blower motor contactor and a small holding charge of refrigerant-22. The units are shipped in the vertical position ready for field installation. They can be installed for horizontal operation by reversing the position of the solid bottom panel with the return air duct flange on the front of the unit.

Publicaciones disponibles en inglés:

Submittal Drawing - Split System Evaporator Blower 10 Tons LA 120 106 KB

Submittal Drawing - Split System Evaporator Blower Unit (7.5 Ton) 117 KB

Technical Guide - Split System Evaporator Blower Unit 378 KB

Repair Parts - F& LA 090 - 120 / EA & HA 090 - 120 85 KB

Technical Guide - Split System Evaporator Blowers 7.5 Nom Ton 367 KB

Beneficios Especiales

• SUPPLY AIR PLENUMS: These fully insulated plenums are available for free standing units located within the conditioned space, are shipped knocked-down for easy field assembly, are finished to match the exterior of the basic unit, and have double deflection grilles that can be adjusted to vary the throw, spread and drop of the supply air.
• RETURN AIR GRILLES: These expanded metal grilles are available for free standing units located within the conditioned space, are finished to match the exterior of the basic unit and are shipped in one piece for easy installation.
• BASES: Bases are available to raise vertical units above the floor. Out-door air may be introduced through these bases by cutting an access opening to accommodate the outdoor air duct connection. These bases are finished to match the exterior of the basic unit. They may have to be insulated in the field for certain appli-cations.
• THREE-PHASE ELECTRIC HEATERS: Electric heaters are available in several capacities to provide maximum flexibility. Both the air conditioning unit and the heater can be selected to precisely match the cooling and heating requirements of the conditioned space. These heaters are designed for easy field installation over the supply air opening of the unit. They have been tested by Underwriters' Laborato-ries and will be shipped with a UL label. Every heater will be fully protected against excessive current and temperature by fuses and two high limit thermostats. Units with electric heat will require only one power supply for both the heating elements and the supply air blower motor, and the power wiring can be protected by either dual element/time delay fuses or an inverse time circuit breaker.

The convertible York Sunline 2000™ Series commercial rooftops line combines standard high-efficiency and advanced-economizer controls with unprecedented installation flexibility and low-installed costs. A single footprint size serves all units from 3 to 6 tons. Offered with Natural Gas heat.This new DM036-072 line also has our Simplicity control board standard on every unit.

Beneficios Especiales

• Simplicity Control Board
  Installation time and costs are reduced by easy power and control wiring.
• All units are factory-wired, piped, charged, and tested prior to shipment.
• Factory-installed options such as stainless steel heat exchanger, electric heating elements, single enthalpy economizer, high static drive blower motor, coil guard, dirty filter switch, hinged filter door, and tooless access panels further reduce installation costs.

• BAS factory mounted controls include Novar, Honeywell, Johnson, and CPC.
  Factory mounted supply and return air smoke detectors.
• Gas and electric utility knockouts are provided on unit side and bottom for easy connections.
• Convertible airflow design means no panel cutting is required, and no accessory panel is necessary.
• Wide range of indoor airflows using belt-drive blowers.
• Durable finish, made of powder-painted, galvanized steel to meet 750-hour salt-spray test demands.
• Full-perimeter base rails are permanently attached to provide a solid unit foundation and fork lift access.
• Compressor is internally protected against high pressure and temperature.
  Grooved copper tubes and enhanced aluminum- fin construction improve heat transfer.
• Heat exchangers are corrosion-resistant, with aluminized steel tubular construction for durability and long service life.
• Permanently lubricated condenser and evaporator fan motor bearings need no annual maintenance.
• Complete line of field-installed accessories, propane and high-altitude conversion kits, motorized dampers, single enthalpy economizers, and dual enthalpy sensors are available.

The convertible York Sunline Series commercial rooftops line combines standard high efficiency and advanced economizer controls with unprecedented installation flexibility and low installed costs. This new DM180-300 line also has our Simplicity control board standard on every unit.

Beneficios Especiales

• Simplicity Control Board
• Installation time and costs are reduced by easy power and control wiring.
• All units are factory-wired, piped, charged, and tested prior to shipment.
• Factory-installed options such as stainless steel heat exchanger, electric heating elements, supply and return smoke detectors, disconnect switch, powered or non-powered
• GFI convenience outlet, single enthalpy economizer, power exhaust, high static drive blower motor, phase monitor, coil guard, dirty filter switch, hinged filter door, and tooless access panels further reduce installation costs.
• BAS factory mounted controls include Novar, Honeywell, Johnson, and CPC.

The convertible York Sunline 2000™ Series commercial rooftops line combines standard high-efficiency and advanced-economizer controls with unprecedented installation flexibility and low-installed costs. A single footprint size serves all units from 3 to 6 tons. Offered as cooling only air conditioners with electric heat.

Beneficios Especiales

• All model sizes share a common, compact design cabinet in a single footprint for on-site flexibility.
• Installation time and costs are reduced by easy power and control wiring.
• All units are factory-wired, piped, charged, and tested prior to shipment.
• Factory-installed options further reduce installation costs.
• Electric utility knockouts are provided on unit side and bottom for easy connections.
• Convertible airflow design means no panel cutting is required, and no accessory panel is necessary.
• Wide range of indoor airflows using belt-drive blowers.